Badland winches mounting instructions. Badland Winch Instructions 2019-01-15

Badland winches mounting instructions Rating: 8,2/10 935 reviews

What Mounting Plate Is Needed for a 12000lb Badland Winch?

badland winches mounting instructions

Insert the siren harness lead 4 into the harness clip 3 to keep the harness clear of other components. Re-install the molded plastic bumper guard. I removed the right side panel and the plastic that goes over the gas tank and forward sides, and ran the main wires along with the main wiring harness. It definately will not break. They are likely made in the same China factory and each adds their own small changes.

Next

BadLands 5000lbs Winch installation/review

badland winches mounting instructions

The housing the clutch control is in is mounted to the end plate with a bunch of cap screws. I always say it's better to have and not need than to need and not have. Installer may need to remove rollers to allow cable end to pass through. I'm in the process of mounting a 5000 pound badlands winch in my 09 rzr 800. Harbor Freight Tools has physical retail stores as well as a mail order and eCommerce business.

Next

ATV/Utility Winch Mounting Plate

badland winches mounting instructions

I took it apart after 2 years of hard riding and it looked brand new on the inside. Filed Under: , , , , , , , Tagged With:. Using the instructions provided with the winch, wire accordingly. If necessary, secure the connector wiring to the electrical panel wiring with a cable strap not provided. The U-Bolts will be placed around the tubes and up through the plate and are secured with Nylock Nuts. Place the Cable Stop onto the Winch Cable up against the Winch Hawse. Also I got the 2 year warranty, I figured if it could last 2 years without failure I got my money's worth, and if it failed the day after the warranty expired hopefully I should be able to afford something like the Terra 2500 even though reviews show a few people have problems with the solenoid pack.

Next

Diy Winch Install

badland winches mounting instructions

I have the 5000 pd now on my rex. A hotter climate or a hair dryer or heat gun may have made it easier. Feel free to email me. I think if you unbolt the plate from the rods, And the take the cap screws out, You can rotate the housing. For 2002-2003 Touring and 2003-Later Softail Models: Remove seat following the instructions in the service manual and disconnect the battery, negative - cable first. Do not tighten fully at this time.

Next

2500 lbs. ATV/Utility Electric Winch with Wireless Remote Control

badland winches mounting instructions

They are branded as Bandland Winches by retailer Harbor Freight Tools. See the illustration below for detail. The mount was delivered ontime. Install the front fork and any parts that were removed to access the front forks. These fasteners will be found in the hardware kit that came with the winch.

Next

Harbor Freight Badlands 12K Winch Install/ Review

badland winches mounting instructions

The rear of the motorcycle may have to be raised slightly to allow removal of the splash guard. The winch is now ready to be installed. It spool in and out just fine but rubs on the right side of the fairlead hole. Running the winch in it easily pulled the tree down, and dragged the 4wheeler across the yard with all 4 wheels locked. Push the bumper back into place and reinstall the original bolts. I hooked a chain around the pallet of wood- roughly 8K lbs worth and began to winch. Remove the splash guard mud flap nuts.


Next

Badland 5000# Winch

badland winches mounting instructions

Remove the guard from beneath the fender. Also I'll post back here any problems or praises I have for it as time goes on. Other rigging and accessories 00:48:16 8. All I had to do was drill that hole out and drill one more hole on the opposite side of the plate. That impression Badland Winch Wiring Instructions Badlands Diagram Wireless Remote with regard to Badland Winch Wiring Diagram over can be classed having: placed simply by admin at May, 1 2015.

Next

BadLands 5000lbs Winch installation/review

badland winches mounting instructions

If anyone needs help doing this or does not have the equipment to do it along with other mods or parts installations or repairs. I will mount the fairlead to the bumper itself. Using a piece of dental floss or similar material in a back and forth motion, loosen reflector from fork slider at both ends. The main complaint is that the mount plate does not line up with the holes on the vehicle. When using the winch to raise and lower a blade a cable stop must be installed. Nice design, keep us updated. This would help keep the power cables to a minimum length.


Next